You might be tired of your patios and lawns accumulated with the leaves in your favorite season –the autumn. Trust me, the view is mesmerizing, but it is frustrating when you don’t get a place for your activities.
Having the Ryobi leaf blower isn’t all you need to get the job done. Sometimes, the fuel gets clogged up in the carburetor and stops the engine from starting when you don’t bring the blower into play for longer.
Ryobi leaf blower doesn’t only make cleanup of leaves from the yards but also doesn’t let the debris stay –much quickly and efficiently.
So what’s the catch? If you need to avoid inconveniences during this arduous operation, there’s a dire need to explore the right path.
Starting the leaf blower is a crucial moment that will ensure smooth and fluent operation of the vacuum. So let’s get right into how you’ll start this powerful tool!
Starting a Ryobi Leaf Blower - Step-by-Step Guide
Here we go!
Step 1 - Check the Clogged Parts
If you’ve ever faced that hair-raising moment that your blower isn’t starting when you have got a bunch of work to do, then it’s probably because the carburetor or oil fuel filter is clogged with the left-over oil.
Even if we leave gasoline for up to 30 days in the machine, it will deteriorate to an extent where the engine will not start. Imagine when you leave the oil for a whole good season, what happens to the engine.
If we store the fuel for a long time, it gets thick and dense and performs the task of clogging the engine’s significant parts. Before you store the blower, make sure to remove the left-over oil and clean it.
Now, if you see your carburetor clogged up with oil debris badly, it’s time to rebuild it. According to gearorigin.com, if its condition is worst, then it’s recommended to change it entirely.
Step 2 - Drain the Old Fuel
So yeah, it’s time to uproot the core of many issues –the old fuel. Take an empty fuel container where you’ll add the drained fuel along with a funnel to get the job done.
Place the blower straight onto the table and open the fuel cap. Now, you’ve to pour the fuel into an empty container by using a funnel.
Drain the blower entirely and make sure there are no traces of old gasoline left behind.
Step 3 - Fill the Gasoline
Well, it’s not all about filling your blower tank with gasoline only. You need to maintain the right fuel ratio –that’s given right on your blower’s labeling.
So now you’re going to prepare a fuel mixture. Take an empty container and add one gallon of gasoline into it, followed by adding 4-ounces of 2-cycle oil.
Close the cap and shake the container roughly to get the mixture mixed thoroughly. What’s the ratio in this case, by the way? You’ll see the gas-to-oil ratio reaching 32:1.
But, if you want to scale it down according to your Ryobi’s desired amount, you can do it. Once you prepare this mixture, fill the tank and hook it properly.
Make the vacuum bag tube slide over the exhaust tube unless the bag feels secure and the tabs click.
Step 4 - Set the Switch ON
Once you’re done with fueling up the gear, it’s time to get it started. For that, you have to spin the lever of the throttle and lock it in one position –ON/Full, most probably.
Wait, wait, wait! Most people forget about changing the mode of the machine. And trust me, that’s the reason when you don’t get the desired results.
Make sure you change the level of the switch and lock it on a blower mode. Yes, that’s it!
Step 5 - Prime the Engine
Priming the engine is as important as fueling it up. Do you know what happens when you don’t press a primer button until the fuel starts appearing?
Actually, it has to deal with moving the fuel mixture to the fuel lines and all the way finally into the carburetor. So make sure you’re pressing the primer up to at least five times slowly.
If you don’t see the gas-oil mixture with your eyes, you’ve to continue pressing, which may be up to 10 times. End this step by altering the choke control to the ‘FULL’ position.
Step 6 - Pull the Starter Cord
The most important step where you’re at the doorstep of the initiation process. It would help if you were quite more vigilant and attentive here.
After placing the Ryobi blower on the ground and adjusting the controller to the fast position, it’s time to pull the starter cord and get the job done.
Pull the starter cord sharply from two to five times unless you hear an engine starting sound. But, make sure you’re not pulling the cord more than six times.
Step 7 - Set the Choke to 'Half'
Once you hear that the engine has been started, now it’s time to set the Choke lever to almost ‘half’ position.
After lowering the choke level, pull the starter rope once again up to three to four times until the engine gets started. But wait, there’s a possibility that the engine may not start due to some reason.
Repeat the entire process from priming the bulb to choking and pulling the starter rope. Now, let the machine warm-up and prepare it for 10 seconds.
Step 8 - Run the Machine
Here’s the final step where you’re going to run your blower finally. After setting the choke to the running position by making a vertical line, switch the device on.
Now you have to alter the change-over lever and switch between the vacuum and a blower. Now, you’re good to go with your blower and perform your duty more efficiently than ever before.
And once you’re done with blowing work and want to stop it, press the ‘turtle icon’ place the throttle in the resting position. Lay the engine for up to 10 seconds and flip the switch to the ‘OFF’ button.
The Bottom Line
From some clogging issues to sparking plug and even broken rewind spring, your Ryobi leaf blower may not start if you’re not making it right.
Do you know what makes the Ryobi leaf blower so unique? It’s pretty easy to use if you once inaugurate it properly.
After dealing with all these issues, you have to follow the complete step-by-step guide if you really don’t like mishaps or breakthroughs in your work.