How to Install Ryobi Bump Feed Trimmer Heads: A Guide

How to

how to install ryobi bump feed trimmer head
Spread the love

Maintaining the appearance of lawns and yards may only be a hobby to some, but to others, it is a must.

Every family should know how to install Ryobi bump feed trimmer heads, which is one of the best weed eaters in the market.

Lawns are quite challenging to maintain when it covers an unusually large piece of your home, especially when weeds have grown out of your lawn.

It will make your yard look dirty and unorganized, as well as can become the habitat of new pests.

What Is a Weed Eater?

A weed eater is also commonly known as a “string trimmer”, and it is something necessary for families who want to maintain their lawns.

It is a good investment for clearing out the weeds in your area and maintaining the appearance of your yard.

They do an effective job since weed eaters usually can trim a whole yard for about six hours.

It can also help the elderly with any back problems.

There are different types of weed eaters, depending on what you may need, but the basic principle of a weed eater is to let the string spin fast enough from a center to cut specific materials, like grasses.

Various materials are being used to serve as the “string” in weed eaters, although the most common one is stiff nylon because it stands out on its own and is very light in weight.

The Ryobi Weed Trimmer

The Ryobi Weed Trimmer is one of the best weed trimmers out there with the most effective work, yet the most affordable.

It is an excellent buy with its 26cc engine with low emission and two cycles.

The Ryobi Weed Trimmer boasts its one horsepower accompanied by two, piston rings as its main feature for overall maximum increase in power, which makes work easier and faster.

It also gives users the chance to change trimmers when inappropriate attachment is used.

Thus, you can use some other attachments when you only want to trim the bushes around.

With the use of two-cycle gas, you can minimize emissions, which is good not only for everyone’s health but also for the environment.

Although it can reduce your work time in more than half, depending on the amount of weed you are about to cut, it still maintains the same efficiency to spend more time doing other valuable things.

Advantages

Every lawn area can be covered in about 10 hours, so you will have more time to do other things like gardening or any recreational activities.

It also has a StartEasy flip button where you do not need to pull it much to open its engine.

The product also has a detachable head, so you can use other attachments that you need.

This convenience allows the weed trimmer to become a bush cutter whenever you need it to.

The attachments from other companies are also compatible for use.

Lastly, since it is a two-cycle engine, it has simpler parts, easier to maintain and store, and has less vibration since it has two engines.

Disadvantages

The only downside of using the Ryobi Weed Trimmer is that you have to tolerate its loud noise during operation.

That said, it has a loud noise since it contains a very good engine to sustain its quality.

The fuel economy of the two-cycle Ryobi Weed Trimmer is not that efficient as compared to a four-cycle engine.

When it comes to gas emissions, the Ryobi Weed Trimmer burns oil to be used as its fuel.

Why Should You Buy the Ryobi Weed Trimmer?

The product has a more efficient capability as compared to the other weed trimmers out there in the market.

Even though the Ryobi Weed Trimmer has a loud engine, the quality of work done is way ahead of its other competitors.

The detachable unit head makes it easier to use the Ryobi Weed Trimmer in comparison with other weed trimmers out there.

How to Install Ryobi Bump Feed Trimmer Heads

Ryobi Products is a company famous for their lawn equipment made from gasoline.

One of its famous products includes a complete line of string trimmers.

If the cutting attachment attached to your trimmer has been broken or worn out, owners should remove and replace them; this will only take a few steps and a few minutes.

The bump head spring provides the tension to the bump head knob.

It is done to return the head knob to its proper position after it makes contact with the ground to feed more line.

This spring can get weak through time.

When this happens, the bump head trimmer may feed lines inconsistently, and the bump head spring should be changed immediately and probably a new bump feed head.

how to install ryobi bump feed trimmer head

Here are the steps that you need to take to install a Ryobi Bump Feed Header:

1. Invert the Trimmer

With the Ryobi Weed Trimmer upside down, you can now see the bottom of the lawn tool.

This was done to place the cutting head at the top and in front of you so you can examine the bottom part of the Ryobi Weed Trimmer, where you will install the feed header.

2. Loosen the Bump Head

Loosen the bump head or bump knot by unscrewing it in a counter-clockwise motion to avoid having a loose thread on the screw ridges.

If it shows more resistance, use pliers for more grip and leverage, as well as avoid any unnecessary injuries that may be due to forced pulling.

You should now be able to remove the bump head or bump knot and keep it somewhere safe.

3. Remove Inner Spring Reel

After temporarily removing the bump head, remove the inner string reel from the innermost part of the cutting head and keep it in a safe place.

Avoid breaking or misplacing this inner reel spring to avoid any mishaps.

At this point, you can now see the lower part of the engine shaft.

4. Grasp the Shaft Housing

After you have seen the lower section of the engine shaft, using your non-dominant hand, grasp the shaft housing firmly.

Then using your dominant hand, shake off the cutting hand while gently pulling it out upwards.

Continue making this motion until the cutting head slips off the large hex nut it is on.

5. Replace Cutting Head

Attach the new cutting head to the large hex nut.

Gently press, then return the shaft housing in place.

Make sure that the fitting is firm, and you might have to give a little extra effort in order to tighten the attachments.

That is to avoid any unexpected movements of the reattached shaft housing.

6. Add Spring Reel on the Housing Shaft

As mentioned, the inner spring reel should be attached in the innermost part of the housing shaft.

You will notice that the lower part of the engine shaft will now be hard to see if you have attached the spring reel properly in place.

Make sure that the spring reel is correctly placed on the housing shaft since it is one of the most important innermost parts of the housing shafts.

7. Tighten the Bump Head Back

You now have to return the bump head in place.

Use a clockwise motion to tighten the bump head, while being careful with the other parts.

You may use other tools, like pliers, to put it in place more easily.

That will also avoid any unnecessary muscle strains if you force yourself to do it by hand.

8. Run a Test

To make sure that the installation was successful and the weed trimmer is working properly after you have installed the head, try a little test run before using it on your lawn.

Depending on your ability to handle tools, the above steps can be done in just ten minutes, not wasting any time to start on your scheduled lawn trimming.

Conclusion

The ability to self maintain your lawn maintenance equipment is a must thing to have.

It would cost you a lot less than availing the services of a lawn company to fix their equipment.

If you can already fix your lawn maintenance equipment, then maybe you can also fix others’ instruments.

Step-by-step guidelines, just like the one from above, are beneficial to owners saving their money and are very easy to follow so that you can learn by yourself how to fix them properly.

Not only have you saved more from your savings, but also, you now have the edge of doing your own repairs and maybe the future repairs of others, too.

With the knowledge on how to install Ryobi Bump Feed Trimmer heads in mind, you can even teach your fellow neighbors on how to install the bump feed head of any trimmer properly without consulting the hardware store.

Maybe one day, you can start your own business regarding repairing parts of a weed trimmer and installing bump feed trimmer head.

Maintaining its other parts can also be a part of your business since it is also commonly handled by people who install bump feed trimmer head on weed trimmers.

About the Author

Steve has been gardening for over 20 years now. He enjoys sharing his experiences with others.

Leave a Comment:

Leave a Comment:

Best 12 Tips... for your yard.

Sign up below to get started: