Truly, a weed eater is the most important tool that keeps your yard spick and span by trimming shabbily grown plants, shrubs, and weeds.
But many homeowners complain that the weed eater string keeps going back in, making it difficult to trim the grasses. So, if you’re among them and are looking for a solution, I’ve got you covered with this informative guide. Keep reading!
Why Does My Weed Eater String Keep Going Back In
Let’s put it this way - you’re using the weed eater to get rid of weeds from your garden, and the trimmer string keeps going back inside the trimmer head.
Indeed, it’s a frustrating situation for every gardener and homeowner, but it also makes it challenging to pull off gardening tasks, wasting a lot of energy, time, and effort. But don’t worry, for we’ve got the reasons and solutions for the same.
Ways To Fix Your Weed Eater String That Keeps Going Back Inside The Trimmer Head
1. Tap The Head On The Ground
Anytime the string of your weed eater keeps going back, simply tap the trimmer head on the ground, and it will dispense the line.
However, ensure that you tap the trimmer head when it’s rotating at full speed, or it won’t advance the trimmer line. That’s because the centrifugal forces of the rotating head feed out the line for trimming the grasses and mowing the lawn.
Also, never tap the head on a hard surface, such as rock, concrete, or wood. Instead, you must always tap it on soft surfaces such as grass, or you’ll damage the trimmer head.
2. Replace The String
If your weed eater doesn’t dispense string even after tapping the head multiple times, there’s a high possibility that the line is too short.
When you feed a string that is less than the length specified, it will cause the head to spin more quickly than it should. As a result, the trimmer engine will wear faster than it should, affecting the longevity of your device.
Understandably, you will have to replace the old string line with a new one only then will your device function properly.
3. Replace The Broken Spring
At times, the weed eater string keeps going back inside the trimmer head because of a broken spring.
So, if you’ve fed the correct size spring in the trimmer head, then the spring may be responsible for the malfunctioning of the device. Of course, you’ll have to dispose of the old string and feed a new one by removing the head from the driveshaft or spool from the head, depending on the model you own.
I suggest referring to the instruction manual that comes with the device, as it will walk you through replacing the spring.
4. Load The Line Correctly
Another reason why the string may not advance from the trimmer head is that it may not be looped correctly around the spool.
Usually, the two lengths of the string are wounded around the spool simultaneously, ensuring they don’t cross over. Irrespective of whether your weed eater requires one or two lengths of line, you will have to ensure that they are looped in the direction marked on the spool.
In case they are in the opposite direction, the string won’t advance and will keep going back in the head.
How To Feed String In The Trimmer Head
1. Remove The Spool From The Trimmer Head
First things first, detach or remove the spool from the head of the weed eater by pushing and twisting. However, it’s best to refer to the instruction manual to avoid damaging your device.
2. Feed The New String
After taking out the spool, discard the old string, grab a new reel, and cut the recommended length. Take one end of the string and feed it into the hole that is located in the middle of the spool until you reach the middle of it.
Then take both lengths of the string and wind them around the spool simultaneously, taking care to cross over only when you need to start a new row. When about eight inches of string is left, stop winding and feed both lengths through the hole that you’ll find on the side of the head.
3. Attach The Cover
After feeding the two lengths to the head, place the cover back after putting the spool back in its place. Now lock the cover, and you’re done!
Summing It Up
So, “why does my weed eater string keep going back in the trimmer head?” Hope this guide addresses your query.
But before I sign off, here’s a last piece of advice - don’t forget to check the instruction manual of your device before troubleshooting the issue. With that, I’ll call it a day.
Bye, folks!